Hammerite Direct to Rust Metal Paint Satin Finish
Hammerite Direct To Rust Metal Paint can be
painted directly onto rusty surfaces, and thanks to its
special 3 in 1 formula there is no need to use a primer or
undercoat - saving you precious time!
Touch dry in an hour, Hammerite gives
long-lasting protection and is suitable for use on a wide
range of exterior metal including gates, railings,
drainpipes, guttering and garden furniture.
▶ Apply direct to
rust
▶ Protects for up
to 5 years
▶ No primer or
undercoat required
▶ For metal inside
and outside the home
▶ Available in
smooth, satin or hammered finish
▶ Available in
250ml, 750ml, 2.5L & 5L, 285ml aerosol
Satin - Aerosol Colours
Black
White
Colour accuracy
We've made every
effort to make the colours on screen as close as
possible to the ones you'll use. Unfortunately, we
cannot guarantee an exact colour match. Photographs
and paint chip colour will vary depending on your
screen settings and resolution. If you are unsure of
a colour, we recommend that you see our colour card
in your local store.
Satin - Brushed Colours
Black
White
Colour accuracy
We've made every
effort to make the colours on screen as close as
possible to the ones you'll use. Unfortunately, we
cannot guarantee an exact colour match. Photographs
and paint chip colour will vary depending on your
screen settings and resolution. If you are unsure of
a colour, we recommend that you see our colour card
in your local store.
Hammerite Direct to Rust Hammered Paint
here
Hammerite Direct to Rust Smooth Paint
here
Usage
Direct to Rust Metal Paint Aerosol
Satin Finish can be used for:
▶ Direct to Rust
▶ Fence
▶ Garage door
▶ Garden furniture
▶ Metal Door
▶ Metal gate
Direct to Rust Metal Paint Brushed
Satin Finish can be used for:
▶ Direct to Rust
▶ Fence
▶ Garage door
▶ Garden furniture
▶ Metal Door
▶ Metal gate
Colourful Accessories
Colourful Accessorie
Colourful Corner
Wood and Metal
Wood and Metal
Garden Delights
Garden Delights
Garden Delights
Bench Restoration
Bench Restoration
Freshen up railings
Freshen up railings
Preparation
Preparation - Aerosol
Abrade smooth surfaces and remove all loose and flaking
paint with a wire brush. Remove dirt and dust with diluted
detergent.
Remove grease with Hammerite Brush Cleaner & Thinners.
Then rinse with clean water and allow time to dry.
Spray a test patch of Hammerite Direct to Rust Metal Paint
onto painted surfaces and leave for 1 hour.
If there is no reaction apply Hammerite Direct to Rust Metal
Paint directly to surface. If there is a reaction remove all
paint before applying Hammerite Direct to Rust Metal Paint.
On bare zinc, aluminium and galvanised surfaces, apply
Hammerite Special Metals Primer before applying Hammerite
Direct to Rust Metal Paint.
Preparation - Brushed
1. Abrade smooth surfaces and remove all loose rust and
flaking paint with a wire brush.
2. Remove dirt, dust and grease with diluted detergent.
Rinse with clean water and allow time to dry.
3. Paint a test patch of Hammerite Direct to Rust Metal
Paint Smooth onto painted surfaces and leave for 1 hour.
If there is no reaction apply Hammerite Direct to Rust Metal
Paint Smmoth directly to surface.
4. If there is a reaction, remove all paint before applying
Hammerite Direct to Rust Metal Paint Smooth.
5. On bare zinc, aluminium and galvanised surfaces apply
Hammerite Special Metals Primer before applying Hammerite
Direct to Rust Metal Paint Hammered.
Application
Applications - Aerosol
Store aerosol at room temperature for 2 hours prior to use.
Shake can vigorously, in a vertical motion, until the
agitator ball is heard and then for a further 3 minutes.
Apply light even coats, from a distance of approximately
15cm (6 inches) and keep the aerosol moving.
Do NOT concentrate spray in one spot. Apply 3-4 coats for
maximum protection and allow 15 minutes between coats.
Between coats invert can and spray for 2 seconds to avoid
blockages.
Applications - Brushed
1. Ideal application temperature 8℃ - 25℃.
2. Lightly stir before use. Do not mix vigorously.
3. Do not mix paint from 2 tins or mix colours.
4. Brush application: Do not thin. On previously painted
metal in sound condition, 1 coat should be sufficient. On
bare/rusty metal 2 coats are required. Ensure that all edges
and corners are adequately covered. Do not over-apply as
sagging will occur.
5. Coventional spray application: Thin with Hammerite Brush
Cleaner & Thinners at a ratio of 15% Thinners to Paint. Set
spray gun at 25/35psi and use full fan spray at maximum
volume. Apply 4 thin coats. Allow 1 hour between coats.
Refer to spray equipment manufacturer's guidelines for the
correct and safe use of sprayers.
Cleaning and Storage
After use, remove as much paint as possible from brushes
before cleaning with Hammerite Brush Cleaner & Thinners.
The information contained herein is based on data considered accurate and reliable to the best of our knowledge and belief as of the date compiled. However no warranty is expressed or implied regarding the accuracy of these data or the results to be obtained from the use hereof.
