Eastwood HotCoat Powder - Silver Vein

The Rust Restoration Specialists !

Eastwood Hotcoat Powder Silver Vein

Extremely durable, chip-resistant finish; coat and cure in under an hour.

Size: 1 lb Bag

Product Code: EW10213LB

Quantity

Check out our Product Guide for Common Uses for PPC CO. Products on restoration projects.


ppcco tabs

Eastwood Hotcoat Powder Silver Vein - EW10213LB

Do The Job Right with Eastwood Powders!

▶   Provides extremely durable finish
▶   Contains no environmentally harmful solvents
▶   100% Virgin powder
▶   Impact resistant and flexibility
▶   Good chemical resistance

Eastwood Powders are far superior to liquid coatings. They provide an extremely durable finish that is chip resistant. All Powders are formulated of the highest quality materials and are chemical and fuel resistant. Eastwood Powders are durable enough for under hood applications and heat resistant up to 250℉. They are suitable for any metal surface and most cure at a temperature of 400℉ at 20 minutes after flow out. With Eastwood powders, you can be assured of high transfer efficiency and brilliant colors.

Application

CLEAN - Thoroughly strip and clean your metal part before coating. We recommend Eastwood Pre Painting Prep.

COAT - Apply using Eastwood DIY HotCoat Gun 11671A or the Eastwood Dual Voltage HotCoat Gun 11678.

CURE - Cure the part in an electric oven for recommended time. NEVER use an oven that is used for food.

Specification

Color: Silver Vein
Gloss Level: Gloss
Cure Temperature: 400℉
Cure Time: 20 Minutes after flowout
Coverage: 1/2 lb. of powder is approximately 10-20 sq. ft.

Safety

When applying powder always apply it in a well ventilated area away from heat sparks and open flame. Always use a respirator rated for dust while applying powder. Always store powders in cool (less than 80 degrees Fahrenheit) dry (60 percent or less humidity) well ventilated area away from heat sparks and open flame.

Other Colours

Select Powder Range to see

map
map

Powder Coating Made Easy - Dual Voltage Powder Coating Gun from Eastwood

With our dual-voltage HotCoat gun, you can powder coat interiors and hard-to-reach corners using the low 15,000-volt setting, or switch to the high 25,000-volt setting for multi-coat coverage over larger areas with increased powder adhesion and minimal overspray. Either way, you'll get all the benefits of powder coating in your own shop!

Extremely durable finish
Coat and cure in under an hour!
Easy to apply
Quick color changes
Economical

  • Don
    This is "IT" for auto accessories!!!
    This "Silver Vein" powder coat is one of my favorites! It has a nice, rich semi-gloss textured finish and looks especially nice on suspension parts, bumper brackets and engine tin on my cars. Its very durable and looks just right. You can clear over it if you like glossy, and I'm sure this will make it even more durable. I'd powder coat my whole car with this, if it would just fit in the oven!!!
  • Great color!
    The sample picture does not come close to doing this color justice. This color is a really great color. The final color is really cool looking but It's as cool to watch bake in the oven. I had some brackets done for my old Excursion in this color professionally years ago and what I am coating in my garage now is at least equal in quality to what I paid a shop to do and the color is exactly the same. I shot a coat of the high gloss clear over the silver vein which really makes it "pop" and shine like it's still wet. The trick I used to shoot the clear was to pull the part out of the oven after curing the Silver Vein, let it cool for about 5 minutes then shoot the clear on it. Thicker pieces will still be hot and the clear will actually melt and gloss over right away. I then throw them back in the oven, lower the heat to 375 and back for another 20 minutes. The pieces come out fantastic. I am rebuilding a rock crawling vehicle, a 1972 Jeepster Commando. I am powder coating all of the door handles, hinges, anything chrome in the Satin Black powder (which is great BTW) and I'm doing the tailgate hardware, latches, and other brackets in the Silver Vein (which is actually black with silver bleeding through) and it really accents the satin black items. If you're on the fence about this color, jump over and get some. It will be one of your favorite colors. I'll take some pictures and add them here, Eastwood should but I'll help them and I know it will sell more of this color!
  • Great for engine parts
    My favorite powdercoat color. Used it on my intake manifold, valve covers, air cleaner and more. Requires some practice to get the right result; apply too little and it just comes out as a dark gray, but put it on heavy enough and the black and silver separate resulting in a nice textured effect
  • Great looking
    Very easy powder to use,pictures do this powder no justice, everyone i have showed love this color