U Pol Raptor Ute Liner

Product Code:

UPL.RLB.S4

Excludes Courier Fee

Qty:

Coming Soon to PPCCO RAPTOR Roll-On Application

RAPTOR is one of U-POLs unique super tough protective coating products.

It can be used over a multitude of surfaces and RAPTOR tintable can be tinted to any colour of your choice, with the ability to create both smooth and textured finishes.

Protects against rust, corrosion, damp, and extreme temperature
High coverage up to 12 m² per kit
Provides excellent UV protection
Provides a tight seal, keeping water and fluids out
Resists against fuels, hydraulic oils, animal urine, salt water etc
Easy application: no spray booth required
Can be applied with: Schutz Gun, HVLP Gun, roller or brush

Kit contents 4 x 750ml bottles of base and 1 x 1L RAPTOR hardener.

Application Tips

Substrate Preparation:
Do not apply to bare metal - must be applied over primer or existing 2-pack colour & scuffed
Always clean, scuffed surface with wax & grease remover
Do not apply over 1K primers or U-POL High #5 … instead use a 2K urethane or epoxy primer, or etch primer such as U-POL Acid #8
Observe curing times on etch primers
Raptor is heat-curing and will re-flow uncured primer, allowing acid to bite into Raptor instead of the substrate
Do not apply over exposed OEM seam sealer or uncoated aftermarket seam sealers
Always coat with primer before applying Raptor. When in doubt use an adhesion promoter like U-POL Grip #4
To achieve a clean tape line, spray U-POL Grip #4 along tape edges before Raptor
To assure good adhesion, spray U-POL Grip #4 in areas that are difficult to scuff - under rails, between floor and side panels, etc.
Remove brackets, bolts, hooks and tie-down points where possible and “plug” holes with rolled-up masking tape

Application:
Thinner coats = harder surface … thicker coats = softer surface, reduced texture
Touch dry in <1 hour @ 20oC, light duty cure in 2-3 days @ 20oC and full cure in 5-7 days @ 20oC
One coat will give up to 300 microns film build - 1 litre will cover 2-3m2 (22-32 square feet)
For higher build apply another coat after flash off period
To achieve a flatter textured harder surface Raptor can be reduced up to 10%
Raptor may be applied over itself after full cure for touch ups
Add grit to Raptor before application to make it a high adhesion, extremely durable non-slip coating

Application Over Other Liners:
As a general rule, if any existing liner looks similar to Raptor in hardness and texture, you can apply Raptor over it
Do not apply Raptor over “franchise” bed liners like Rhino or other polyurethanes. Raptor over old epoxy bed liners is OK
Note that aged epoxy tends to get brittle and crack; we recommend grinding it down so that the substrate starts to show through before applying Raptor
Thoroughly scuff existing bed liner and wipe down with wax & grease remover
If you can still see existing bed liner texture, it is not scuffed sufficiently

Tintable Info Sheet
msds

Raptor Tintable Truck Bed Liner Product Information Sheet

The information contained herein is based on data considered accurate and reliable to the best of our knowledge and belief as of the date compiled. However no warranty is expressed or implied regarding the accuracy of these data or the results to be obtained from the use hereof.

Black Info Sheet
msds

Raptor Black Truck Bed Liner Product Information Sheet

The information contained herein is based on data considered accurate and reliable to the best of our knowledge and belief as of the date compiled. However no warranty is expressed or implied regarding the accuracy of these data or the results to be obtained from the use hereof.

Share this product with Friends

Raptor Promo Video

U-POL® RAPTOR® Liner & Protective Coating: Part 1 How to Mix and Apply RAPTOR®

RAPTOR How to Tint and Spray